SUNDAY, OCTOBER 21, 2018
Font Size
Topic From DPMO to Sigma Level

From DPMO to Sigma Level

Home Forums General Forums Tools & Templates From DPMO to Sigma Level

This topic contains 10 replies, has 5 voices, and was last updated by  Mike Carnell 6 months, 2 weeks ago.

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • #702847 Reply

    I have a question regarding DPMO. If you calculate DPMO, why would you want to look up the corresponding sigma level? And does it have any meeting as the DPMO can consist of multiple items with (often) non-normal distribution of some of these items.

    #702876 Reply

    It’s easier to compare small numbers. More importantly, the sigma level is statistically more meaningful – Look at a bell curve. The differences get finer as you approach the tails and sigma level accounts for that while DPMO doesn’t. For instance the difference between 2 and 3 sigma is 42,851 DPMO. The difference between 3 and 4 is just 2,636. For your second question, if you aren’t looking at a single specification it’s mixing apples and oranges. But it doesn’t really matter as long as you’re accurately counting defects and opportunities and you’re clear about what’s included. The distribution is irrelevant.

    #702903 Reply

    If the opportunities are truly the value added ones, then DPMO is a fantastic tool to measure across services, product lines, etc. And since sigma level is well known, it’s great.

    ONLY problem is the question has to be asked–did they shift the number or do straight read from Z table. And….some tables are shifted already “being helpful”.

    #702969 Reply

    The Sigma level with DPMO is a approximation to normal distribution from binomial distribution; according with central limit theory, its due to the DPMO measure the number of trials and success (%) in each sample or success (%) in the Critical characteristic of the part. Remember that a part could have many opportunities to evaluate (CTQ’s).

    Example : Suppose that we have a process with this characteristic:
    Example:
    Units/shift = 30,000
    Defective parts = 300
    Defects observed = 350
    Opportunities = 15
    Dpu = 350/30,000 = .011
    DPMO = (.011/15) x 1,000,000 = 777
    Yield : 1-(0.011/15) = 99.9922%
    ZBench : 3.164 *From normal distribution tables
    Sigma Level: 4.664
    CPk Process: 1.55

    #703277 Reply

    @Straydog Thanks. Never thought about that. This implies that it is more and more difficult to achieve higher sigma scores, the higher your current score is. Am i right?

    @gomezmgab Thanks. But this implies that the transformation from binominal to a normal distribution can only be done when p is not that high, isn’t?

    #703315 Reply

    @erik2018 That’s sort of right. Keep in mind that the closer you get to zero defects the smaller the change necessary to raise sigma level. Improving a few DPMO won’t make much difference if your sigma level is low. But it will the closer you get to 6 sigma or even better where those small DPMO improvements get more and more difficult.

    #704315 Reply

    you do not need P to perform the calculation, the approximation assumes that if the size of the sample is large enough, it will approach normal …

    #704531 Reply

    Thanks! By the way, why is it based on a binominal distribution? Isn’t it about defectives (a part could have many ctq’s/defectives) which corresponds with a Poisson distribution?

    #704741 Reply

    @erik2018 You need to remember that there are a lot of metrics that get used and they can all represent the same number. The opportunity count is what is important (as much as I hate to say that because it opens the door for people to play with jacking up opportunity counts rather than fixing things). The Op count reflects complexity. If I was Jack Welch in 1996 and I had GE lighting and GE Aircraft Engines and I am measuring first pass yield then I have that whole apples to oranges issue. If I use DPMO now it is normalized and I can make the comparison. converting it to a sigma value doesn’t change anything it represents but it confuses a lot of people. I only use it with management and only when I have to. When you are dealing with operations people I use DPU. It is a number that makes sense in the context of their jobs.

    I wouldn’t waste a lot of time on this. It doesn’t move you any closer to fixing anything.

    Just my opinion.

    #704759 Reply

    Well said, @Mike-Carnell Pretty much the only thing DPMO or Sigma Level give us is a metric that can be theoretically used for objective comparison between unlike products/processes. And that’s likely to be misleading since we can always miscount or “game” the counts.

    #704794 Reply

    @Straydog That has always been the issue with DPMO. If you have defects/opportunities there are 2 ways to play the game 1. reduce defects which is what we are supposed to do 2. Increase opportunities which is the game a lot play particularly management. The whole opportunity counting game goes all the way back into Motorola. Unless a person is completely stupid and you see rework everywhere and they line is supposed to be at 4 sigma or greater then they are playing the denominator game.

Viewing 11 posts - 1 through 11 (of 11 total)

Register Now

  • Stop this in-your-face notice
  • Reserve your username
  • Follow people you like, learn from
  • Extend your profile
  • Gain reputation for your contributions
  • No annoying captchas across site
And much more! C'mon, register now.

Reply To: From DPMO to Sigma Level
Your information:






5S and Lean eBooks

Six Sigma Online Certification: White, Yellow, Green and Black Belt

Six Sigma Statistical and Graphical Analysis with SigmaXL
Six Sigma Online Certification: White, Yellow, Green and Black Belt
Lean and Six Sigma Project Examples
GAGEpack for Quality Assurance
Find the Perfect Six Sigma Job

Login Form